現如今環氧地坪的成熟，被使用的地點很多，比如停車場、工廠車間等地方，然而在施工完成后我們要注意監測環氧地坪涂料的黏度，這樣可以保證環氧地坪完成后的質量和使用時間。不過值得注意的是，在測量時一定要注意以下幾點，否則很難操作。

Nowadays, epoxy floor is mature and used in many places, such as parking lots, factories and workshops. However, after construction, we should pay attention to monitoring the viscosity of epoxy floor coatings, so as to ensure the quality of the finished epoxy floor and the use time. However, it is worth noting that when measuring, we must pay attention to the following points, otherwise it is very difficult to operate.

(1)測定的規定溫度應在21-25度之間。因?yàn)闇囟冗^(guò)高，測定的黏度比較低，溫度過低，黏度比較高，不是標準值。

(1) the prescribed temperature should be between 21-25 degrees. Because the temperature is too high, the viscosity of the measurement is relatively low, the temperature is too low, the viscosity is relatively high, it is not the standard value.

(2)每次測完要清潔涂-4杯，選用所測涂料相應的溶劑，防止測定小孔被堵。

(2) after each test, -4 cup should be cleaned and the corresponding solvent should be selected to prevent the small hole from being blocked.

(3)先用手指或器具堵嚴小孔漏嘴，倒?jié)M100ml涂料，用玻璃棒將氣泡和多余試樣倒入凹槽，防止測樣不到或超過標準。

(3) First plug the small hole leak with finger or instrument, fill 100 ml paint, and pour the bubble and surplus sample into the groove with glass rod to prevent the sample from failing or exceeding the standard.

(4)迅速移開手指時，同時啟動秒表，待試樣流束剛中斷時立即停止秒表，計時。

(4) When the finger is quickly removed, the stopwatch is started at the same time, and the stopwatch is stopped immediately when the sample beam is interrupted.

環氧砂漿地坪

Epoxy mortar floor

對環氧地坪涂料產品黏度的經驗檢測方法是，經攪拌后，用棒挑起涂料進行觀察。正常的涂料應自由降落而不斷，如有中斷而回縮現象，說明該涂料較稠。一般棒上的涂料與桶內涂料在很短時間內會連接不斷的流淌，連接距離為30-50cm，即是近于刷涂的程度。小于30cm，表明涂料的黏度太小，即涂料太稀;大于50cm，表明黏度太大，即涂料太稠。這種以符合施工要求為準，同時又通過多次實踐應用，不用黏度計測定的黏度，稱為工作黏度。

The empirical test method for the viscosity of epoxy floor coatings is to observe the coating with stick after stirring. Normal coatings should be allowed to fall freely and continuously. If there is any interruption, the shrinkage will show that the coating is thicker. Generally, the paint on the rod and the paint in the barrel will connect continuously in a very short time, the connection distance is 30-50 cm, that is, close to the degree of brushing. Less than 30 cm, indicating that the viscosity of the coating is too small, that is, the coating is too thin; greater than 50 cm, indicating that the viscosity is too big, that is, the coating is too thick. This kind of viscosity is called working viscosity, which is based on the construction requirement and has been used for many times without viscometer.

通過測定黏度，可以觀察涂料貯存一段時間后的聚合度，按照不同施工要求，用適合的稀釋劑調整黏度，以達到刷涂、鏝涂、批刮施工所需的不同黏度指標。所以施工過程中這一步時不可少的，在施工時一定要注意工人是否偷工減料。

By measuring the viscosity, we can observe the degree of polymerization of the paint after storage for a period of time, and adjust the viscosity with suitable diluents according to different construction requirements, so as to achieve the different viscosity indexes required for brushing, upsetting and batch scraping. So this step in the construction process is indispensable, in the construction must pay attention to whether the workers jerry-built.