環氧地坪漆常見的固化問題主要有：固化不均、固化不良、表面發黏、表面發白和不固化。下面環氧地坪漆廠家就給大家分析環氧地坪漆常見固化問題的原因。環氧地坪漆漆膜部分出現軟和硬的涂膜狀態。這主要是環氧地坪材料主漆與固化劑在混合容器里攪拌不良，混合不均勻。環氧地坪漆廠家建議大家在進行配料時采用攪拌器充分?jǐn)嚢柙偈褂谩?/p>

The common curing problems of epoxy floor paint are uneven curing, poor curing, surface sticking, surface whitening and non-curing. The following epoxy floor paint manufacturers will give you an analysis of the reasons for the common curing problems of epoxy floor paint. 

1、固化不均

1. Non-uniform curing

環氧地坪漆漆膜部分出現軟和硬的涂膜狀態。這主要是地坪材料主漆與固化劑在混合容器里攪拌不良，混合不均勻。地坪漆廠家建議大家在進行配料時采用攪拌器充分?jǐn)嚢柙偈褂谩?/p>

The film of epoxy floor paint is soft and hard. This is mainly due to the poor mixing and uneven mixing of the main paint and curing agent in the mixing container. Floor paint manufacturers recommend that we use mixer to mix and reuse the ingredients.

2、固化不良

2. Poor curing

整個漆膜固化狀態差，重物或人員走動有壓痕。這種現象主要是施工環境溫度太低、反應不完全，或固化劑加入比例不符。光磊地坪漆廠家提醒大家地坪漆最佳施工溫度是在5-35℃，配料時采用電子秤嚴格按照配比進行調配材料。

The whole film is in poor solidification state, and there are indentations in the movement of heavy objects or personnel. This phenomenon is mainly due to the construction environment temperature is too low, the reaction is not complete, or the proportion of curing agent does not match. Guanglei floor paint manufacturer reminds you that the best construction temperature of floor paint is 5-35 C. When mixing, electronic scales are used to mix materials strictly according to the proportion.

3、表面發黏不干

3. Surface stickiness

初凝時，環氧地坪漆表面發黏。主要原因是整個涂料的攪拌不充分，造成未反應的成分在表面下游離。

The surface of epoxy floor paint sticks when it is first set. The main reason is the inadequate stirring of the whole coating, which causes the unreacted components to be separated from the surface.

4、表面發白

4. Surface whitening

環氧地坪漆表面仿佛有層云霧。這主要是因為施工環境潮氣重，涂膜上易結霜，或固化劑含水，使得固化劑里的胺析出產生白霧集結在表面。

There seems to be a cloud on the surface of epoxy floor paint. This is mainly due to the heavy humidity of the construction environment, the easy frosting on the coating, or the moisture content of the curing agent, which makes the amine precipitation in the curing agent produce white fog on the surface.

5、不固化

5. Non-curing

環氧地坪漆施工后一直不固化。主要原因是固化劑加量不準或加錯;環境溫度過低(低于5℃以下)。

Epoxy floor paint does not solidify after construction. The main reason is that the dosage of curing agent is inaccurate or wrong; the ambient temperature is too low (below 5 C).